Eva Smart Plug
Introduction
The small but powerful 230V / 16A / 3680W Eva Smart Plug provides you with control over power efficiency and consumption. This Smart Plug is part of the Eva product family and is ZigBee 3.0 certified.
You can use the Eva Smart Plug in other Zigbee-based smart home systems as long as your smart home provider has support for the plug.
Installation
During startup, the LED alternately flashes red and blue. It will then enter pairing mode, and the red LED will rapidly flash 3 times. To set up the Eva Smart Plug, follow the instructions in your app.
For the Eva App:
- Open the Eva Smart Home App
- Add a new device and choose Eva Smart Plug
- Scan the QR code on the plug
- Follow the instructions in your app to complete the setup process
Test the device by using the push-button of the Smart Plug or the app to turn power ON/OFF
Factory reset
If the plug does not enter pairing mode, press and hold the button for at least 10 seconds to reset the smart plug and initiate the pairing mode.
LED indications
| LED COLOR | LED STATUS | EXPLANATION |
| OFF | Power is OFF | |
| Blue | ON | Power is ON |
| Blue | Flashing | Smart Plug is in timer mode |
| Red/blue | Flashing |
2. Flashing 3 times RED, while BLUE is on. Smart Plug is in pairing mode and power is ON |
| Red | ON | Indicating, that devices connected are consuming too much current. Remove connected devices from Smart Plug and restart Smart Plug by taking Smart Plug out of socket and re-inserting Smart Plug into socket |
| Red | 3 fast flashes | Smart Plug is in pairing mode |
| Red | Slow flash |
Flashes every half second – pairing mode for Touchlink Flashes every second – lost connection to hub/gateway. Flashes every other second – not connected to a hub/gateway |
| Red | Flashes very fast | Temperature too high. Disconnect Smart Plug and wait until it has cooled down |
Using the button
| ACTION | DESCRIPTION | EXPLANATION |
| Press | ON/OFF Toggle | Turns ON/OFF a device plugged into your Smart Plug e.g. a desk lamp |
| Press for more than 10 seconds | Start pairing mode and factory reset |
Resets Smart Plug to factory default and starts pairing mode. Note: A factory reset unpairs the Smart Plug from your gateway. |
| Press for more than 5 seconds | Start Zigbee Touchlink pairing | Starts touchlink pairing on the Smart Plug to connect directly with devices e.g. connect a scenario switch directly with your Smart Plug. |
Important safety information
Read this manual before attempting to install the device! The Smart Plug is for indoor use only.
- Do not use in wet or humid locations. This includes near washing machine, sink, shower, swimming pool/bathtub or any other area with water or moisture present.
- Do not use the Smart Plug together with other power adapters or power strips.
- Do not connect any device consuming more than 16A.
- For your own safety, do not use the Smart Plug in case of any visible damage.
- The Smart Plug is not a replacement for your regular power fuse!
- Failure to observe recommendations included in this manual may be dangerous or cause a violation of the law. The manufacturer will not be held responsible for any loss or damage
Appendix
Information on disposal for users of waste electrical & electronic equipment
This symbol on the product and accompanying documents means that used electrical and electronic equipment (WEEE) should not be mixed with general household waste. For proper treatment, recovery and recycling, please take this product to designated collection points where it will be accepted free of charge. Alternatively, in some countries, you may be able to return your products to your local retailer upon purchase of an equivalent new product.
Disposing of this product correctly will help save valuable resources and prevent any potential negative effects on human health and the environment, which could otherwise arise from inappropriate waste handling. Please contact your local authority for further details of your nearest designated collection point. Penalties may be applicable for incorrect disposal of this waste, in accordance with your national legislation
Software updates
Software updates can be released by the manufacturer to fix bugs or enhance functionality after the product has been released. Updated software versions released will not impact continued compliance with applicable rules
Technical specifications
| General | For use with CEE 7/4 (Schuko) socket Degree of protection: IP20 |
| Local Communication |
Radio protocol: Zigbee 3.0 Transmission power: 19dBm Router functionality |
| Ratings |
Voltage: 230V AC Operating temperature: 0 to +40° C |
Declaration of Conformity
Datek Smart Home AS declares that the equipment described in this document, is in compliance with the essential requirements and other relevant provisions of EU Directive 2014/53/EU. If you require a copy of the original signed DoC, please visit https://hjelp.evasmart.no/hc/no
Datek Smart Home AS
Voldgata 8
2000 Lillestrøm
Comments
0 comments
Please sign in to leave a comment.